SVIP DNA200 - 200W Temp Control Box Mod

FREE EXPRESS SHIPPING

Cigreen

$229.95 AUD  

Hurry! Only 0 left at this price!

  • SVIP DNA200 - 200W Temp Control Box Mod
  • SVIP DNA200 - 200W Temp Control Box Mod
  • SVIP DNA200 - 200W Temp Control Box Mod
  • SVIP DNA200 - 200W Temp Control Box Mod
  • SVIP DNA200 - 200W Temp Control Box Mod
  • SVIP DNA200 - 200W Temp Control Box Mod

This product is currently sold out.


This is not a toy. This is not a beginner's mod. This is a highly-customisable, high wattage, temperature-controlled box mod. 

  • Chip: Authentic Evolv DNA 200;
  • Adjustable 510 pin
  • Battery: 3S Li-po 11.1V 1500mAh, 35C battery (built-in);
  • Variable wattage: Wattage can be adjusted from 1W to 200W in 0.1W increment;
  • Resistance range (stand coil): 0.1~2.0 ohm;
  • Resistance range (temperature control coil): 0.08~1.0 ohm);
  • Operating temperature control: 200'F~600'F (100'C~300'C);
  • Can be charged via USB (micro USB cable included);
  • Large OLED displays battery level, voltage, wattage, resistance and temperature

Getting started - IMPORTANT

These units do not come pre-charged, and require a USB Recovery Charge (via the eScribe Software** to bring it to life. (plugging the mod into any old USB port will not charge it from 0% battery)

1. Download and install eScribe from EVOLV (http://www.evolvapor.com/software/SetupES.exe)
2. Connect yout device to your computer via Micro-USB cable
3. Once your device is recognised by eScribe (should be automatic), open device monitor (1)
    • You will notice that the charge in the top left corner should be at 0.00Wh, even though the unit is plugged in and should be charging
    4. Click on DIAGNOSTICS (2)> ADVANCED (3)> PERFORM USB RECOVERY CHARGING... (4)
    5. Once the USB recovery charging (trickle charge) has given your mod life (leave it for about five minutes), you can then charge the device from any free USB port- Note, charging can take approximately 3-5 hours to 100%

      Read this quick-start guide on ECF for info on getting started with eScribe
      Genuine EVOLV DNA200 chip - Spec Sheet / Manual Here

       

      Minimum

      Typical

      Max

      Output Power

      1 Watt

       

      200 Watts

      Output Voltage

      .5 Volt

       

      9.0 Volts

      Output Current, continuous

       

       

      50.0 Amps

      Output Current, instantaneous peak

       

       

      55.0 Amps

      Atomizer Resistance, temperature sensing wire, cold

      See Graph

      .10 Ohm

      See Graph

      Atomizer Resistance, kanthal wire

      See Graph

      .20 Ohm

      See Graph

      Temperature Limit

      200°F

      450°F

      600°F

      Input Voltage

      9.0 Volts

      11.1 Volts

      12.6 Volts

      Input Current

      .5 Amps

      9.0 Amps

      23.0 Amps

      Screen On Current

       

      18mA

       

      Quiescent Current

       

      4.5 mA

       

      Power Down Current

       

       

      25uA

      Efficiency

       

      97%

       

      Weight

       

      15g

       

      Footprint

      .71” x 2.80”

       

      18mm x 71mm

      Thickness

       

      .32”

       

      Screen size

       

      .91” OLED

       

       

       

       **eScibe is currently only available on Windows- there is a discussion on using a Macintosh computer with eScribe here: http://evolvapor.forumchitchat.com/post/mac-suppport-7534870

      Share this

      Pin Post Plus

      Similar Products

      days
      hours
      minutes
      seconds